Thanks for visiting !
Originator of flat triggers for Taurus PT111 G2 & Slim
We are engaged in niche manufacturing. Filling a void by providing items that might not otherwise be produced. Evolving and innovating.
Originator of the flat trigger shoe for the AR15 mil spec trigger
Please verify that you ordered the exact trigger for the gun that you needed a trigger for. The triggers are absolutely not interchangeable among the brand of a gun. Each specific model requires its own trigger regardless if it is for the same brand of gun. Also a failure to fit can be caused by an improper installation. All of the triggers should go into the gun freely or it is not being installed correctly and is out of proper alignment. Extra tuning could be required to properly fit the trigger to your gun.
Usually yes, but we do NOT GUARANTEE that our Canik triggers are a "drop in" installation in every gun and fitting might be required for your gun. In most cases they will be a "drop in", but due to variations in tolerances of certain parts, fitting by your gunsmith could be necessary. However, we are aware that it is difficult to offer a high performance trigger that will drop in every single gun , especially with the reduced operating envelope of our triggers. So we have engineered the trigger to be optimized for certain variances in the guns. Qualified gunsmith installation is absolutely required for your safety, the protection of your firearm and for proper tuning if it is required. The trigger bar (or action bar) can also vary in thickness sometimes requiring filing the slot to fit it . None of this is rocket science and is easily performed single surface fitting that a qualified gunsmith can do during the installation of the trigger.
All of our products are sulfuric acid anodized for a finish over the aluminum. The colors vary from one batch to the next. Also dyeing the colors is not an exact science. The photos in the website also may depict different colors due to lighting or reflections.
Trigger styles for Canik pistols.
A basic description for our available triggers for the Canik would be;
Fat Daddy and Fat Daddy ll = target, plinking @.421wide. Only difference is the two additional angles on the FDII. The Fat Daddy Classic has the same attributes of the Fat Daddy but with a curved face. Many prefer the traditional feel of the curved trigger. These three styles of triggers are very wide and not recommended for small hands or short fingers.
The Master is similar to the classic, being a curved style, but with relieved sides for better access to the drop safety lever.
Racer & Champion for competition that requires fast access to the drop safety lever (relieved sides) @.421 top and bottom. Again only difference is the two angles added to the Champion.
Vanguard & Pro = more narrow face (@.375 front edge and still .421 overall) for those that do not desire the wider Fat Daddy . The Pro has two additional angles to assist in consistent finger placement. The "Zombie Pro" differs from the "Pro" only in that it has a curve at the top that transitions into a flat with a more pronounced hook on the tip and is only available in solid colors. Otherwise they are identical in other features.
Our available inventory is on the website under the category for the specific model of Canik that you have. (They are not interchangeable between all models.)
#1"Do you have a trigger for my Canik SA mod2 ?" Yes we do. Any trigger that we offer as fitting the SFX models will also fit your SA Mod 2 (but it will NOT fit a non MOD 2 SA model). If your pistol does not have "Mod 2" on the side, it is not a Mod 2.
#2 Do you have trigger for my Canik SA model ? NO
#3 Do you have a trigger for my Canik DA (double action ) model ? NO
We do NOT offer international shipping.
NO ! We design around known factory geometry only !
It totally depends on the gun and the person doing the installation. XD (XDM) triggers typically take less than five minutes to install. XDS can require 90 minutes or more due to the complicated nature of the design. Canik will depend on the experience and/or ability of your installer. Some report doing it in 15 minutes. Others need all day. Please have a qualified gunsmith do your Canik trigger installation. Taurus is relatively complex and need caution to avoid the loss of pins, detent balls and springs. For reasons of varying degrees of complexity and safety we always stress that installations be done by a qualified gunsmith.
NO Custom orders accepted
We are not able to offer color combinations or styles on an individual requested basis. The cost incurred in doing that is much greater than the profit margin, resulting in a loss. Items must be produced in quantities in order to maintain our low prices. If an item is not available on this website, then it is temporarily out of stock and will be replaced as soon as possible.
IMPORTANT NOTICE !!!!
We no longer are maintaining a waiting list or accepting any "notify me when available" requests as it is has become too disruptive to normal stocking operations. NO switching, swapping or changing of safety lever or trigger colors or styles !
(All prices are at dealer tier , NO other discounts are available)
Please verify your address before placing your order. We are not responsible for incorrect addresses